Build a Inexpensive Car Protection Unit Circuit Diagram

This is a simple Inexpensive car Protection Unit Circuit Diagram. This circuit to protect car stereo, etc from pilferage that costs less and requires no adjustments in the car but a good car cover. Place the circuit at your bedside and bring the two wires from the unit to the car (parked outside your home) and connect one wire-end to the cover and the other to the ground, with both wire-ends shorted by some weight such as a brick. So outwardly the mechanism is not visible.

Circuit of car protection unit with alarm

If someone tries to remove the cover, the alarm of the circuit starts sounding to alert you. The alarm can be switched off by resetting it using switch S1.

The car protection circuit comprises two timer ICs: one for the alarm circuit (see IC2 in Fig.1) and the other to indicate that the battery has taken over as the power source (see IC3 in Fig. 2). Normally, the protector operates off AC mains and the battery takes over only when mains fail. As the battery current is not high, the battery will last long.

As long as the two wires remain shorted, transistor T1 remains cut off. When shorting is removed, transistor T1 gets forward biased and its collector voltage drops to trigger IC2 and the piezobuzzer starts sounding.

 battery-takeover indicator

If mains fails, the battery-takeover indicator (shown in Fig. 2 and connected to points A, B and C in Fig. 1) immediately gets triggered at pin 2 of IC3. Its high output activates the battery-operation alarm for a couple of seconds. IC1 draws power from the battery to activate the protection unit.

After setting up the unit properly and shorting both the wires, press test switch S2. If there is no fault in the circuit, the alarm will sound. Now release test switch S2 and momentarily press reset switch S1 to switch off the alarm.

Sourced By:  EFY Author : M. Venkateswaran and T.E. Parthasarathy

Read More

Build a Digital Electronic Lock Circuit Diagram

This Digital Electronic Lock Circuit Diagram shown below uses 4 common logic ICs to allow controlling a relay by entering a 4 digit number on a keypad. The first 4 outputs from the CD4017 decade counter (pins 3,2,4,7) are gated together with 4 digits from a keypad so that as the keys are depressed in the correct order, the counter will advance. As each correct key is pressed, a low level appears at the output of the dual NAND gate producing a high level at the output of the 8 input NAND at pin 13.

Read : Cheap Bicycle Alarm Schematics Circuit

Digital Electronic Lock Circuit Diagram

 

The momentary high level from pin 13 activates a one shot circuit which applies an approximate 80 millisecond positive going pulse to the clock line (pin 14) of the decade counter which advances it one count on the rising edge.

Read : Emergency Light and Alarm Circuit Diagram

A second monostable, one shot circuit is used to generate an approximate 40 millisecond positive going pulse which is applied to the common point of the keypad so that the appropriate NAND gate will see two logic high levels when the correct key is pressed (one from the counter and the other from the key). The inverted clock pulse (negative going) at pin 12 of the 74C14 and the positive going keypad pulse at pin 6 are gated together using two diodes as an AND gate (shown in lower right corner).

Read : Burglar Alarm With Timed Shutoff Circuit Diagram

The output at the junction of the diodes will be positive in the event a wrong key is pressed and will reset the counter. When a correct key is pressed, outputs will be present from both monostable circuits (clock and keypad) causing the reset line to remain low and allowing the counter to advance. However, since the keypad pulse begins slightly before the clock, a 0.1uF capacitor is connected to the reset line to delay the reset until the inverted clock arrives.

Read : 5 Zone alarm Circuit Diagram

The values are not critical and various other timing schemes could be used but the clock signal should be slightly longer than the keypad pulse so that the clock signal can mask out the keypad and avoid resetting the counter in the event the clock pulse ends before the keypad pulse. The fifth output of the counter is on pin 10, so that after four correct key entries have been made, pin 10 will move to a high level and can be used to activate a relay, illuminate an LED, ect. At this point, the lock can be reset simply by pressing any key. The circuit can be extended with additional gates (one more CD4011) to accept up to a 8 digit code.

Read :  Alarm Control Keypad Circuit Diagram

The 4017 counting order is 3 2 4 7 10 1 5 6 9 11 so that the first 8 outputs are connected to the NAND gates and pin 9 would be used to drive the relay or light. The 4 additional NAND gate outputs would connect to the 4 remaining inputs of the CD4068 (pins 9,10,11,12). The circuit will operate from 3 to 12 volts on 4000 series CMOS but only 6 volts or less if 74HC parts are used. The circuit draws very little current (about 165 microamps) so it could be powered for several months on 4 AA batteries assuming only intermittent use of the relay.

Read More

Build a 12 14 Volt 3A Anti RF Filtered Power supply Circuit Diagram

How to Build a 12-14 Volt 3A - Anti-RF Filtered Power supply Circuit Diagram. This is not easy but you can do it . This Anti-RF Filtered Power supply Circuit Diagram is dedicated for use with rf equipments like, linear amplifiers, transmitters, receivers, and in every application that clean an-noisy signal is required. 

The circuit is very simple and you can drive it with a 220V/18V/3A transformer at the pins 1and 2.The regulator used here is the LM350K and make sure you place a good heat-sink to it because it gets too hot if current gets near to 3A. 

 12-14 Volt 3A - Anti-RF Filtered Power supply Circuit Diagram

Parts list
R1 = 220 Ohm 1/4W
R2 = 1,8 KOhm 1/4W
R3 = 330 Ohm 1/4W
 P1 = 100 Ohm
C1,C2,C3 = 4.700uf/25V
C4 = 100pf ceramic
C6 = 100uf/25V electrolitic
D1..4 = 1N5400-4 or RAX GI 837U
F1 = 5A
IC1 = LM350K

For Data Sheet Contact with us here

Read More

Build a Voice Scrambler or Descrambler Circuit Diagram

This Voice Scrambler or De-scrambler Circuit Diagram uses an NE602 as an inversion mixer. U2 is set to run at about 2.5 to 3.5 kHz. U3 drives a loudspeaker. Because speech inversion scrambling is its own inverse, the circuit will also descramble . 

Voice Scrambler or Descrambler Circuit Diagram

Read More

Build A Relay Toggle Switch

Half of RL1 and RL2 manipulate the switching and the other is connected to an application. Relays are 200 ohms above ground and at one point are referenced to positive that turns them off.

Description:

RL1 (which is off) applies plus voltage from its armature and latches RL2 “on”. The application terminals are set to [A]. The condition changes when S1 is activated, voltage is applied to RL2 latching RL1 “on” releasing S1 turns RL2 “off”. RL2’s armature is then directed to R1. Terminals are set to [B].

When S1 is pressed again, the relays negative side are referenced to positive, RL1 turns “off” (there’s no current flow). RL2 turns “on” when S1 is released, terminals are set to [A]. There is slight lag between relays depending on how long S1 is held.

Relay Toggle Switch Circuit Diagram

Note: 

If different relays are used, adjustment of R1’s value may be required. For example, OEG relays (12vdc, 270 ohm coil) need R1 at 60 - 70 ohms. The prime motivation for this design was to avoid using toggle switches for my audio control panel. Another plus, it can be controlled from a remote transmitted pulse.

Read More

10 Channel LED Sequencer

this is how to Build 10 Channel LED Sequencer may you have another idea, will be good if you share here.

Read More