Low Cost Universal Battery Charger Schematic

Low cost solution for charging of each NiCd and NiMh batteries

Here is the circuit diagram of a low price universal costr for NiCD - NiMH batteries. This circuit is Ideal for automobile use. It has capability to transform a primes adapter in to a costr . This one can be used to cost mobile phone, toys, moveables, video batteries, MP3 gamers, ... and has selectable cost present. An LED is situated in circuit to indicate charging. Can be built on a basic purpose PCB or a veroboard. I hope you in point of fact love it.

Picture of the circuit: 

 A Low Cost Universal Charger Circuit Schematic

Circuit diagram:

A Low Cost Universal Charger Circuit Diagram

Parts:

R1 = 120R-0...5W
R2 = See Diagram
C1 = 220uF-35V
D1 = 1N4007
D2 = 3mm. LED
Q1 = BD135
J1 = DC Input Socket

Specifications:

• Ideal for in car use.
• LED charge indication.
• Selectable cost current.
• Charges Ni Cd or NiMH batteries.
• Transforms a primarys adapter into a costr.
• Charge cellular phone, toys, transportables, video batteries …

Features:

• LED perform indication.
• Power provide polarity protected.
• Supply current: similar as cost current.
• Supply voltage: from 6.5VDC to 21VDC (depending on used battery)
• Charge present (±20%): 50mA, 100mA, 200mA, 300mA, 400mA. (selectable)

Determining the availability voltage:

This desk indicates the minimum and most voltages to supply the charger. See provide voltage choice chart under.

Example:

To cost a 6V battery a minimum supply voltage of 12V is needed, the utmost voltage is then 15V.

Voltage choice:

Voltage Selection Chart For Low Cost Universal Battery Charger

Determining the cost current:

Before constructing the circuit, you have to determinate how a lot present will probably be used to charge the battery or battery pack. It is a good suggestion to cost the battery with a present that is 10 occasions smaller then the battery capability, and to charge it for about 15 hours. If you double the charge current , then that you may charge the battery in half of the time. Charge present selection chart is positioned in diagram.

Example:

A battery pack of 6V / 1000mAh will additionally be charged with 100mA during 15 hours. If you need to charge quicker, then a cost present of 200mA can be utilized for approximately 7 hours.

Caution:

The larger cost present, the extra essential the cost time need to be checked. When faster charging is used, you should discharge the battery totally sooner than charging. Using a cost present of 1/10 of the capacity will increase the lifetime of the battery. The cost time can easily be doubled with out damaging the battery.

Note:

• Mount the transistor in conjunction with the heatsink on the PCB, bend the leads as important. Take care that the metal again of the transistor touches the heatsink. Check that the leads of the transistor don't touch the heatsink.

Source : http://www.ecircuitslab.com

Read More

14W CLASS A AMPLIFIER CIRCUIT USING 2N3055 SCHEMATIC DIAGRAM

14W CLASS A AMPLIFIER CIRCUIT USING 2N3055 SCHEMATIC DIAGRAM

Many early amplifiers operated in Class A, but as output powers rose above 10W the problems of heat dissipation and power supply design caused most manufacturers to turn to the simpler, more efficient Class B arrangements and to put up with the resulting drop in perceived output quality. Why Class A ? Because , when biased to class A, the transistors are always turned on, always ready to respond instantaneously to an input signal. Class B and Class AB output stages require a microsecond or more to turn on. The Class A operation permits cleaner operation under the high-current slewing conditions that occur when transient audio signal are fed difficult loads. His amplifier is basically simple, as can be seen from the block diagram.

Read More

3 VOLT 6 VOLT MINI AUDIO AMPLIFIER SCHEMATIC DIAGRAM

3 VOLT - 6 VOLT MINI AUDIO AMPLIFIER SCHEMATIC DIAGRAM



The potentiometer circuit can be used to control volume. Capacitor C1 and C2 are designed to filter supplyvoltage If the battery separator is used as operations offer source.For using batteries C1 and C2 are not required.



IC TDA7052 is a mono output amplifier in 8-comng Head DI package (DIP). The device is designed primarily for battery-operated portable audio circuits. Features include TDA 7052, no external components needed, no switch-on or switch-off button sounds great overall stability and very low power consumption (quiescent current of 4 mA), low THD, it is not necessary any cooler and short-circuit proof.



Profit TDA 7052 is set internally at 40 dB. . Compensate for the reduction of output power due to low voltage TDA7052 uses Bridge-Tied-Load principle

(BTL), which can provide power about 1 to 2 W RMS (THD = 10%), 8 ohm load to the power supply 6 V.

Read More

14 W AUDIO AMPLIFIER TDA2030 CIRCUIT SCHEMATIC DIAGRAM

14 W AUDIO AMPLIFIER TDA2030 CIRCUIT SCHEMATIC DIAGRAM

Resistors should be at least 1/4W types with 1% tolerance recommended. I used 0.6W 1% metal film resistors and they work well. Capacitors I used were electrolytic cans for C2, C5 and C6. At the time of building, I did not have enough 100uF caps so I used 220uF caps instead, this will not cause trouble, unless you use caps that are smaller than 100uF for C5 and C6.



C1 can be electrolytic, I used a tantalum myself (dont ask why, since they are actually more expensive). Some readers may want to use a polyester capacitor for the input (C1), this would work too but I am not sure whether any benefit will arise from the extra expense. Other capacitors (bypass caps C3 and C4. and C7) are ideally polyester caps. Mylar may be used but I prefer polyester caps and they are not expensive unless you get large values.



The values of R5 and C8 are worked out from the equations in the datasheet, but I used 1.8k ohm for R5 and 220pF for C8 and they work fine. Diodes should be 1N4001 or similar (make sure you solder them in the right way round).



A good heatsink is important and this should be a large size with good thermal conductivity. When you operate the TDA2030 from the (recommended) split rail power supply, you must insulate the device from the heatsink using a mica washer or similar. With single rail supply, this is not needed.

Read More