Thursday, 11 April 2013

0 Comments
Posted in Arrangement, Art, Business

Automatic TV Lighting Switch

The author is the happy owner of a television set with built-in Ambilight lighting in the living room. Unfortunately, the television set in  the bedroom lacks this feature. To make up for this, the author attached a small lamp to the wall to provide background lighting, This makes  watching television a good deal more enjoyable, but it ’s  not the ideal solution. Although the TV set can be  switched off with the remote  control, you still have to get out of bed to switch off the lamp.

Circuit diagram :
Automatic TV Lighting Switch-Circuit-Diagram

Automatic TV Lighting Switch Circuit Diagram

Consequently, the author devised this automatic lighting switch that switches the background light on and off along with the T V set. The entire circuit is fitted in series with the mains cable of the TV set, so there’s no need to tinker with the set. It works as follows: R1 senses  the current drawn by the TV  set. It has a maximum value  of 50 mA in standby mode,  rising  to around   500 m A  when  the  set  is  operating. The voltage across R1 is limited by D5 during negative  half- cycles  and  by  D1– D4  during positive half-cycles.  T he  voltage  across  these  four diodes charges capacitor C1 via D6 during positive  half-cycles. This voltage drives the internal LED of solid-state switch TRI1 via R2, which causes the internal triac to conduct and pass the mains voltage to the lamp.   Diode D7 is not absolutely necessary, but  it is recommended because the LED in the  solid-state switch is not especially robust  and cannot handle reverse polarisation. Fuse  F1 protects the solid-state switch against  overloads. T he  value  of  use d  here  (10 Ω)  for  resistor R1 works nicely with an 82-cm (32 inch)  LCD screen.

With smaller sets having lower  power consumption, the value of R1 can be  increased to 22 or 33 Ω, in which case you  should use a 3-watt type. Avoid using an  excessively high resistance, as otherwise TRI1 will switch on when the TV set is in standby mode.  Some TV sets have a half-wave rectifier in the  power supply, which places an unbalanced  load on the AC power outlet. If the set only  draws current on negative half-cycles, the cir-cuit won’t work properly. In countries with  reversible AC power plugs you can correct  the problem by simply reversing the plug. Compared with normal triacs, optically cou-pled solid-state relays have poor resistance  to high switch-on currents (inrush currents).

For this reason, you should be careful with  older-model TV sets with picture tubes (due  to demagnetisation circuits). If the relay fails,  it usually fails shorted, with the result that the TV background light remains on all the time. If you build this circuit on a piece of perf-board, you must remove all the copper next  to conductors and components carrying  mains voltage. Use PCB terminal blocks with a spacing of 7.5 mm. This way the separation between the connections on the solder  side will also be 3 mm. If you fit the entire  arrangement as a Class II device, all parts of  the circuit at mains potential must have a  separation of at least 6 mm from any metal  enclosure or electrically conductive exterior  parts that can be touched. 
 
 
 
http://streampowers.blogspot.com/2012/06/automatic-tv-lighting-switch_11.html 
0 Comments
Posted in Arrangement, Art, Business

Pump it up Mp3 Booster

MP3 players are all the rage these days. The smaller ones in memory-stick format are particularly easy to take with you; your very own ‘personal sound system’ on the move! It’s when you want others to share your taste in music that you find these players to have a lack of power. You can get round this problem with the help of the MP3 booster, a small amplifier that can be used to connect your MP3 player directly to your Hi-Fi. When you next invite your friends to a party you can ask them to bring their ‘personal music’ as well as the usual drinks!

But first we have to build this booster! The small battery-powered players have an output signal that is more than sufficient to drive a set of 32 Ohm headphones. You’ll often find that with an output of 1mW the sound pressure level (SPL) produced can reach up to 90 dB. This would be sufficient to cause permanent damage to your hearing after only one hour! The maximum output voltage will then be around 200mV. This, however, is insufficient to fully drive a power amplifier. For this you’ll need an extra circuit that boosts the output voltage.

Power amps usually require 1 V for maximum output, hence the signal has to be amplified by a factor of five. We will also have to bear in mind that quieter recordings may need to be amplified even more. We’ve used a simple method here to select the gain, which avoids the use of potentiometers. After all, the MP3 player already has its own volume control. We decided to have two gain settings on the booster, one of three times and the other ten times. Amplifiers IC1A and IC1B (for the right and left channels) are housed in a single package, a TS922IN.

The output signal of the MP3 player is fed via a stereo cable and socket K1 to the inputs of the amplifiers. The gain depends on the relationship between resistors R2 and R1 (R6 and R5 for the other channel) and is equal to ten times. When you add jumper JP1 (JP2), resistor R3 (R7) will be connected in parallel with the negative feedback resistor R1 (R6), which causes the gain to be reduced to about three. When you start using the booster you can decide which gain setting works best for you.

Circuit diagram:
MP3 Booster Circuit Diagram

Resistor R4 (R8) takes the amplified MP3 signal to the output socket K2 (K3). A cable then connects these phono sockets to the input of your power amplifier. The resistors connected in series with the output (R4 and R8) are there to keep the booster stable when a long cable is connected to its output. Cables have an unwelcome, parasitic capacitance. This capacitive effect could (due to phase shifts of the signal) affect the negative feedback of the booster in such a way that a positive feed back occurs, with the result that the booster oscillates and possibly damages the power amplifier!

The resistors (R4 and R8) effectively isolate the output of the booster from the parasitic capacitance of the output cable. They also protect the booster outputs from short circuits. We’ve used a TS922IN opamp in this booster because it can operate at very low supply voltages (the maximum is only 12 V!), but can still output a reasonable current (80 mA max.). For the supply we’ve used rechargeable batteries (e.g. NiCd or NiMH cells) so that we don’t need a mains supply.

To keep the number of cells required as small as possible, we’ve chosen a supply voltage of 5 volt; this can be supplied by four rechargeable batteries. It is also possible to use four ordinary, non-rechargeable batteries; it’s true that the supply voltage then becomes a bit higher (6 Volts), but that won’t cause any harm. Since we’ve used a symmetrical supply for the booster (2 x 2 batteries), it will be easiest if you use two separate battery holders, each with two AA cells. The two holders are connected in series.

Make sure that the batteries are connected the right way round; the positive of one always has to be connected to the negative of the next. This also applies to the connection between the two battery holders. S1A/B is a double pole switch, which is used to turn both halves of the battery supply on or off simultaneously. If you can’t find the (dual) opamp we’ve used (or an equivalent), you could always use standard opamps such as the NE5532, TL082 or TL072. These do need a higher supply voltage to operate properly. In these cases you should use two 9 V batteries and replace resistor R9 with a 15 kΩ one.

Do take care when you connect the circuit to your power amplifier because the output signal can be a lot larger and you could overload the power amplifier. (Although you’re more likely to damage the loudspeakers, rather than the amplifier!) (Please note that these two 9 V batteries can’t be used as a supply for the TS922IN!) In our circuit we’ve used a stereo jack socket for the input and phono sockets for the output because these are the most compatible with MP3 players and power amplifiers respectively. If you wanted to, you could solder shielded cables directly to the circuit instead, with the correct plugs on the ends. You’ll never find yourself without the correct connection leads in that case!
 
 
 
Streampowers
0 Comments
Posted in Arrangement, Art, Business

How to Make a Simplest Compact 1 Watt LED Driver Circuit at 220V 110V Mains Voltage

Circuit diagram.
Seetharaman’s words about the circuit: I am sending you a table lamp made from defunct energy saver lamp with broken tubes. CFL converted into LED lamp. Most of the components will be available in ones scrap box. Few components available in the CFL PCB also can be used.
Procedure
1. Carefully remove the broken glasses
2. Open the assembly carefully
3. Remove electronics and discard
4. Assemble the circuit in dot matrix PC or on a 1mm laminate sheet.
5. Cut a round laminate sheet with (scissor)
6. Mark the position of the 6 round holes on the sheet
7. Drill the holes to suit the LEDs to flush fit in the six holes
8. Use a dab of adhesive to keep the LED assembly in position
9. Close the assembly
10. Ensure the internal wiring does not touch each other
11. Now test on 230Volt AC
Your nice compact table lamp / puja room lamp / passage lamp is ready for use.
0 Comments
Posted in Arrangement, Art, Business

Lambda Probe Readout For Carburettor Tuning

A lambda probe (or oxygen sensor) can be found on the exhaust system of most cars running on unleaded fuel. Having reached its normal operating temperature (of about 600 degrees Celsius!) the lambda probe supplies an output voltage proportional to the amount of residual oxygen measured in the exhaust gas.

This information is indicative of, among others, the air/fuel ratio supplied by the carburetor(s) and hence the combustion efficiency. In modern car (and motorcycle) engines, this information is used to (electronically) adjust engine parameters like ignition timing and fuel injection. The indicator described here is intended for permanent installation on a motorcycle of which the air/fuel ratio needed to be watched, with the obvious aim engine power tuning after fitting a different set of carburetors. Apart from this obvious technical use the unit’s bright LEDs will no doubt attract the attention of curious motorcyclists.

Lambda Probe Readout For Carburettor Tuning

At the local junkyard a single-wire lambda probe may be salvaged from a wrecked car. Once a suitable nut has been found, the probe can screwed into the exhaust pipe of the motorcycle, at about 30 cm from the cylinders.  Since we’re talking of welding and drilling in an expensive (chrome-plated) exhaust pipe, you may find that actually fitting the probe is best left to specialists!  The starting point for the design of a suitable electronic indicator is that in the noble art of carburetor tuning an air/fuel ratio of 14.7 to 1 is generally considered ‘perfect’, the range covering 16.2 to 1 (‘lean’) to 11.7 to 1 (‘rich’). The perfect ratio typically corresponds to a probe output voltage of 0.45 V. 

 Referring to the circuit diagram, that is the input level at which 5 of the 10 LEDs will light, including the green one, D5. If one of the red LEDs lights, the mixture is definitely too rich. Note that in general it is better to have a mixture that is a little to rich than one that’s on the lean side, hence a yellow LED lights between the green LED and the first red one. Also note that the engine needs to be at its normal operating temperature before a meaningful indication is obtained.
 
 
 
streamcircuits
0 Comments
Posted in Arrangement, Art, Business

12KV High Voltage Generator

The hobby circuit below uses an unusual method to generate about 12,000 volts with about 5uA of current. Two SCRs form two pulse generator circuits. The two SCRs discharge a 0.047uF a 400v capacitor through a xenon lamp trigger coil at 120 times a second.

Circuit Project:12KV High Voltage Generator
 
The high voltage pulses produced at the secondary of the trigger coil are rectified using two 6KV damper diodes. The voltage doubler circuit at the secondary of the trigger coil charges up two high voltage disc capacitors up to about 12KV. Although this circuit can’t produce a lot of current be very careful with it. A 12KV spark can jump about 0.75 of an inch so the electronic circuit needs to be carefully wired with lots of space between components.
 
 
 
Source by : Streampowers
0 Comments
Posted in Arrangement, Art, Business

150W BRIBGE AMPLIFIER WITH TDA 7294 CIRCUIT DIAGRAM

150W BRIBGE AMPLIFIER WITH TDA 7294 CIRCUIT DIAGRAM

As you can see, there are provisions to use TDA7294 well. This circuit is almost identical, but a specification higher. There are links on the board to connect contacts 1 and 5 (it should not be connected to the TDA727). Use TDA7294, fees can run bridged (BTL or bridge tied load) to about 150 W at 8 ohms. I think P87B be used to provide phase signal is necessary for BTL operation. Although it is common to see AMP as a reversal, there is a very low resistance at first, and may lead to unacceptable pressures and possible distortion. P87B be managed separately by each amplifier, and the best way to control the amplifiers.While parallel operation is often recommended, I strongly recommend that you run the amps in parallel. There are very strict requirements for greater tolerance for parallel operation – usually amplifiers must correspond to 0.1% or more for all audio traffic and beyond. A very low output resistance of members, even inconsistencies 100mV (instantly, any voltage and frequency) can cause large amounts of current flowing through the circuits. Although 0.1O resistors are usually offered, inconsistencies 100mV voltage (0.15% at the peak voltage 60V) 0.5A cause a circulating current. This leads to overheating and protection of anger involved.

Wednesday, 10 April 2013

0 Comments
Posted in Arrangement, Art, Business

14 W AUDIO AMPLIFIER TDA2030 CIRCUIT SCHEMATIC DIAGRAM

14 W AUDIO AMPLIFIER TDA2030 CIRCUIT SCHEMATIC DIAGRAM

Resistors should be at least 1/4W types with 1% tolerance recommended. I used 0.6W 1% metal film resistors and they work well. Capacitors I used were electrolytic cans for C2, C5 and C6. At the time of building, I did not have enough 100uF caps so I used 220uF caps instead, this will not cause trouble, unless you use caps that are smaller than 100uF for C5 and C6.



C1 can be electrolytic, I used a tantalum myself (dont ask why, since they are actually more expensive). Some readers may want to use a polyester capacitor for the input (C1), this would work too but I am not sure whether any benefit will arise from the extra expense. Other capacitors (bypass caps C3 and C4. and C7) are ideally polyester caps. Mylar may be used but I prefer polyester caps and they are not expensive unless you get large values.



The values of R5 and C8 are worked out from the equations in the datasheet, but I used 1.8k ohm for R5 and 220pF for C8 and they work fine. Diodes should be 1N4001 or similar (make sure you solder them in the right way round).



A good heatsink is important and this should be a large size with good thermal conductivity. When you operate the TDA2030 from the (recommended) split rail power supply, you must insulate the device from the heatsink using a mica washer or similar. With single rail supply, this is not needed.



    Total Pageviews