Friday, 2 August 2013

0 Comments
Posted in Arrangement, Art, Business

Ni cad Charger Circuit Diagram

Ni-cad charger with current and voltage limiting. Lamp LI will glow brightly and the LED will be out when the battery is low and being charged, but the LED will be bright and the light bulb dim when the battery is almost ready. Ll should be a light bulb rated for the current you want (usually the battery capacity divided by 10). Diode D1 should be at least 1 A, and Z1 is a 1W zener diode with a voltage determined by the full-charge battery voltage minus 1 V. After the battery is fully charged, the circuit will float it at about battery capacity divided by 100 mA.

Ni-cad Charger Circuit Diagram


Ni-cad Charger Circuit Diagram

Thursday, 1 August 2013

0 Comments
Posted in Arrangement, Art, Business

Reuse Old Mobile Phone Battery for LED lighting

Normally mobile batteries have a lifespan of 2-5 years under normal usage. But then we have to replace them. Nowadays there are cheap replacement batteries which cost no more than 1$. But these low cost batteries run only 6-12 months. What to do with the used batteries, which can’t be reused in mobiles? Well, easy solution is to use the batteries in a circuit that requires less current. We can use them for LED lighting.

Do you have old unusable Mobile battery?
Hacks and Mods: Reuse Old Mobile Phone Battery for LED lighting
Normally mobile batteries have a lifespan of 2-5 years under normal usage. But then we have to replace them. Nowadays there are cheap replacement batteries which cost no more than 1$. But these low cost batteries run only 6-12 months. What to do with the used batteries, which can’t be reused in mobiles?
Hacks and Mods: Reuse Old Mobile Phone Battery for LED lighting
Well, easy solution is to use the batteries in a circuit that requires less current. We can use them for LED lighting. Thus your automatic lighting emergency light is ready which runs by your waste Mobile Battery.

Wednesday, 31 July 2013

0 Comments
Posted in Arrangement, Art, Business

DC Motor Speed Controller

This circuit takes benefit of the voltage drop across bridge rectifier diodes to provide a 5-position variable voltage supply to a DC fan or other small DC motor. It is not as environment friendly as a change-mode circuit but it has the advantages of simplicity and no swaping hash. The 4 full-wave bridges are linked so that every has two pairs of sequence diodes in parallel, giving a voltage drop of about 1.4V, relying on the burden present.

Circuit diagram:
DC Motor Speed Controller Circuit Diagram

The rotary swap should have \"make before break\" contacts which will have to be rated to take presents as a lot as about an amp or so. For better currents, better rated bridge rectifiers and a suitably rugged rotary swap (or solenoids) will most definitely be required. If you want to have smaller voltage steps, that you must use the commoned AC inputs on the bridge rectifiers to provide intermediate steps on the velocity swap.

Author: Stephen Butcher,

Tuesday, 30 July 2013

0 Comments
Posted in Arrangement, Art, Business

Ultrasonic Radar Circuit


This circuit named ultrasonic radar, where this circuit can in applying at security system house and or other security and safety system. in principle this circuit consisted of transmitter and receiver which transmitter and receiver can work with the same frequency, if both having different frequency hence this circuit cannot work. For circuit transmitter is given in symbol T, which frequency yielded by two NAND gates, causing yields signal multi vibrator, this signal which will be sent by transmitter then bound signal from transmitter in comparing to signal which in yielding by receiver, at receiver in symbol R. which entering signal strengthened by TR3 and strengthened again by IC OP-Amp 741. The signal from Op-Amp then returned by IC 2 here signal compared to which then is sent to which NAND gate if happened difference of frequency hence will activate TR1 and TR2 for in attributing to siren or indicator lamp.

Monday, 29 July 2013

0 Comments
Posted in Arrangement, Art, Business

How to Make an Accurate 7 Stage Op Amp Controlled Mains Voltage Stabilizer Circuit


In this article we discuss an interesting circuit which can be used  for controlling our mains AC line fluctuations and for producing very accurate stabilized voltage outputs for our domestic electrical appliances.

More innovative circuits HERE.

The circuit concept is rather very simple. It uses discrete op amps wired up as comparators to sense the voltage levels.



As can be seen in the diagram, each op amps inverting inputs are provided with sequentially incrementing voltage refrence levels through a series of presets which drops a certain amount of voltage across itself.

Each op amp compares this voltage with the common sample mains AC voltage level supplied to the op amps non inverting inputs.

As long as this sample voltage is below the refrence level the respective op amps keep their outputs low and the subsequent transistor relay stages remain inactive, however in case the voltage levels tends to shift from its normal range, the relevant relays trigger and toggle the transformer taps so that the output is appropriately equalized and corrected.

For example if the input AC voltage tends to fall, the upper relays may get triggered connecting the relevant higher voltage taps with the output and vice versa in case the voltage shoots upwards.

Here the op amp output inter-connections makes sure that only one optocoupler and therefore only one relay gets activated at a time.

Parts List

P1---P8 = 10 K Preset,

A1---A8 = IC 324 (2 Nos)

R1---R8 = 1 K,

All diodes = 1N4007,

All relays = 12 volts, 400 Ohms, SPDT,

Opto Couplers are all = MCT2E or equivalent,

Transformer = Pink Tap is normal voltage tap, the upper taps are in the decrementing order of 25 Volts, while the lower taps are in the incremental order of 25 volts.



Thursday, 25 July 2013

0 Comments
Posted in Arrangement, Art, Business

Auto gain Control op amp Circuit Diagram

An audio signal applied to VI is passed through the operational amplifier 741, U2. After being amplified, the output signal V2 is sampled and applied to a negative voltage doubler / rectifier circuit composed of diodes CRI and CR2, with the capacitor C1. The resulting negative voltage is used as a control voltage which is applied to the door] 2N5485 FET Q1. Capacitor C2 and resistor R2 form a filter for smoothing the voltage rectified audio control. The lFET is connected between pin 2 of the MC3340P grounded by a resistor of 1 kohm.

 Auto gain Control op-amp Circuit Diagram
Auto gain Control op-amp Circuit Diagram


As the voltage applied to the gate of FET] becomes more negative in magnitude, the channel resistance of FET] increases causing lFET to function as a voltage-controlled resistor. The MC3340P audio attenuator is the heart of the MCO. It is capable of 13 dB of gain or almost - 80 dB of attenuation as a function of external resistor placed between Pin 2 and ground. An increase in resistance decreases the gain from the MC3340P. The gain of the circuit is not entirely a linear function of the external resistance, but such behavior is similar across much of the gain / attenuation range. An input signal applied to the input of the AGC will cause the gate volt age the proportion lFET become negative. Accordingly, the JFET increases the resistance of the pin 2 to ground the MC3340P causing a reduction in gain. In this way, the AGC output is kept almost constant. source by next.gr

Datasheet file1: Click here to download LM741.pdf datasheet.
Datasheet file2: Click here to download MC3340P.pdf datasheet.
Datasheet file3: Click here to download 2N5485.pdf datasheet.
Datasheet file4: Click here to download 1N270.pdf datasheet.



Wednesday, 12 June 2013

0 Comments
Posted in Arrangement, Art, Business

Resistors

The resistors function is to reduce the flow of electric current.
This symbol is used to indicate a resistor in a circuit diagram, known as a schematic.
Resistance value is designated in units called the "Ohm." A 1000 Ohm resistor is typically shown as 1K-Ohm ( kilo Ohm ), and 1000 K-Ohms is written as 1M-Ohm ( megohm ).

There are two classes of resistors; fixed resistors and the variable resistors. They are also classified according to the material from which they are made. The typical resistor is made of either carbon film or metal film. There are other types as well, but these are the most common.
The resistance value of the resistor is not the only thing to consider when selecting a resistor for use in a circuit. The "tolerance" and the electric power ratings of the resistor are also important.
The tolerance of a resistor denotes how close it is to the actual rated resistence value. For example, a ±5% tolerance would indicate a resistor that is within ±5% of the specified resistance value.
The power rating indicates how much power the resistor can safely tolerate. Just like you wouldnt use a 6 volt flashlight lamp to replace a burned out light in your house, you wouldnt use a 1/8 watt resistor when you should be using a 1/2 watt resistor.

The maximum rated power of the resistor is specified in Watts.
Power is calculated using the square of the current ( I2 ) x the resistance value ( R ) of the resistor. If the maximum rating of the resistor is exceeded, it will become extremely hot, and even burn.
Resistors in electronic circuits are typicaly rated 1/8W, 1/4W, and 1/2W. 1/8W is almost always used in signal circuit applications.
When powering a light emitting diode, a comparatively large current flows through the resistor, so you need to consider the power rating of the resistor you choose.

Rating electric power

For example, to power a 5V circuit using a 12V supply, a three-terminal voltage regulator is usually used.
However, if you try to drop the voltage from 12V to 5V using only a resistor, then you need to calculate the power rating of the resistor as well as the resistance value.

At this time, the current consumed by the 5V circuit needs to be known.
Here are a few ways to find out how much current the circuit demands.
Assemble the circuit and measure the actual current used with a multi-meter.
Check the components current use against a standard table.
Assume the current consumed is 100 mA (milliamps) in the following example.
7V must be dropped with the resistor. The resistance value of the resistor becomes 7V / 0.1A = 70(ohm). The consumption of electric power for this resistor becomes 0.1A x 0.1A x 70 ohm = 0.7W.

Resistance value
    As for the standard resistance value, the values used can be divided like a logarithm.
    For example, in the case of E3, The values [1], [2.2], [4.7] and [10] are used. They divide 10 into three, like a logarithm.
    In the case of E6 : [1], [1.5], [2.2], [3.3], [4.7], [6.8], [10].
    In the case of E12 : [1], [1.2], [1.5], [1.8], [2.2], [2.7], [3.3], [3.9], [4.7], [5.6], [6.8], [8.2], [10].
    It is because of this that the resistance value is seen at a glance to be a discrete value.
    The resistance value is displayed using ( the colored bars/the colored stripes ), because the average resistor is too small to have the value printed on it with numbers.
    You had better learn the color code, because almost all resistors of 1/2W or less use the color code to display the resistance value.


Fixed Resistors
    A fixed resistor is one in which the value of its resistance cannot change.
Carbon film resistors
This is the most general purpose, cheap resistor. Usually the tolerance of the resistance value is ±5%. Power ratings of 1/8W, 1/4W and 1/2W are frequently used.
Carbon film resistors have a disadvantage; they tend to be electrically noisy. Metal film resistors are recommended for use in analog circuits. However, I have never experienced any problems with this noise.
The physical size of the different resistors are as follows.





This resistor is called a Single-In-Line(SIL) resistor network. It is made with many resistors of the same value, all in one package. One side of each resistor is connected with one side of all the other resistors inside. One example of its use would be to control the current in a circuit powering many light emitting diodes (LEDs).
In the photograph on the left, 8 resistors are housed in the package. Each of the leads on the package is one resistor. The ninth lead on the left side is the common lead. The face value of the resistance is printed. ( It depends on the supplier. )
Some resistor networks have a "4S" printed on the top of the resistor network. The 4S indicates that the package contains 4 independent resistors that are not wired together inside. The housing has eight leads instead of nine. The internal wiring of these typical resistor networks has been illustrated below. The size (black part) of the resistor network which I have is as follows: For the type with 9 leads, the thickness is 1.8 mm, the height 5mm, and the width 23 mm. For the types with 8 component leads, the thickness is 1.8 mm, the height 5 mm, and the width 20 mm.

 
 

Metal film resistors
    Metal film resistors are used when a higher tolerance (more accurate value) is needed. They are much more accurate in value than carbon film resistors. They have about ±0.05% tolerance. They have about ±0.05% tolerance. I dont use any high tolerance resistors in my circuits. Resistors that are about ±1% are more than sufficient. Ni-Cr (Nichrome) seems to be used for the material of resistor. The metal film resistor is used for bridge circuits, filter circuits, and low-noise analog signal circuits.

From the top of the photograph
1/8W (tolerance ±1%)
1/4W (tolerance ±1%)
1W (tolerance ±5%)
2W (tolerance ±5%)

Rough size
Rating power
(W)
Thickness
(mm)
Length
(mm)
1/823
1/426
13.512
2515

 Variable Resistors

There are two general ways in which variable resistors are used. One is the variable resistor which value is easily changed, like the volume adjustment of Radio. The other is semi-fixed resistor that is not meant to be adjusted by anyone but a technician. It is used to adjust the operating condition of the circuit by the technician. Semi-fixed resistors are used to compensate for the inaccuracies of the resistors, and to fine-tune a circuit. The rotation angle of the variable resistor is usually about 300 degrees. Some variable resistors must be turned many times to use the whole range of resistance they offer. This allows for very precise adjustments of their value. These are called "Potentiometers" or "Trimmer Potentiometers.
In the photograph to the left, the variable resistor typically used for volume controls can be seen on the far right. Its value is very easy to adjust.
The four resistors at the center of the photograph are the semi-fixed type. These ones are mounted on the printed circuit board.


The two resistors on the left are the trimmer potentiometers.

This symbol is used to indicate a variable resistor in a circuit diagram




There are three ways in which a variable resistors value can change according to the rotation angle of its axis.
When type "A" rotates clockwise, at first, the resistance value changes slowly and then in the second half of its axis, it changes very quickly.
The "A" type variable resistor is typically used for the volume control of a radio, for example. It is well suited to adjust a low sound subtly. It suits the characteristics of the ear. The ear hears low sound changes well, but isnt as sensitive to small changes in loud sounds. A larger change is needed as the volume is increased. These "A" type variable resistors are sometimes called "audio taper" potentiometers.
As for type "B", the rotation of the axis and the change of the resistance value are directly related. The rate of change is the same, or linear, throughout the sweep of the axis. This type suits a resistance value adjustment in a circuit, a balance circuit and so on.
They are sometimes called "linear taper" potentiometers.
Type "C" changes exactly the opposite way to type "A". In the early stages of the rotation of the axis, the resistance value changes rapidly, and in the second half, the change occurs more slowly. This type isnt too much used. It is a special use.
As for the variable resistor, most are type "A" or type "B". 
 




 Other Resistors
 There is another type of resistor other than the carbon-film type and the metal film resistors. It is the wirewound resistor.
A wirewound resistor is made of metal resistance wire, and because of this, they can be manufactured to precise values. Also, high-wattage resistors can be made by using a thick wire material. Wirewound resistors cannot be used for high-frequency circuits. Coils are used in high frequency circuits. Since a wirewound resistor is a wire wrapped around an insulator, it is also a coil, in a manner of speaking. Using one could change the behavior of the circuit. Still another type of resistor is the Ceramic resistor.
These are wirewound resistors in a ceramic case, strengthened with a special cement. They have very high power ratings, from 1 or 2 watts to dozens of watts.

These resistors can become extremely hot when used for high power applications, and this must be taken into account when designing the circuit. These devices can easily get hot enough to burn you if you touch one.
The photograph on the left is of wirewound resistors.
The upper one is 10W and is the length of 45 mm, 13 mm thickness.
The lower one is 50W and is the length of 75 mm, 29 mm thickness.
The upper one is has metal fittings attached. These devices are insulated with a ceramic coating.

The photograph on above is a ceramic (or cement) resistor of 5W and is the height of 9 mm, 9 mm depth, 22 mm width 

Thermistor ( Thermally sensitive resistor ) 

The resistance value of the thermistor changes according to temperature.
This part is used as a temperature sensor.


There are mainly three types of thermistor.
    NTC(Negative Temperature Coefficient Thermistor)
      : With this type, the resistance value decreases continuously as the temperature rises.
    PTC(Positive Temperature Coefficient Thermistor)
      : With this type, the resistance value increases suddenly when the temperature rises above a specific point.
    CTR(Critical Temperature Resister Thermistor)
      : With this type, the resistance value decreases suddenly when the temperature rises above a specific point.
The NTC type is used for the temperature control.

The relation between the temperature and the resistance value of the NTC type can be calculated using the following formula.

    R: The resistance value at the temperature T
    T: The temperature [K]
    R0: The resistance value at the reference temperature T0
    T0: The reference temperature [K]
    B: The coefficient

    As the reference temperature, typically, 25°C is used.
    The unit with the temperature is the absolute temperature(Value of which 0 was -273°C) in K(Kelvin).
    25°C are the 298 kelvins.

Resistor color code

    Total Pageviews