This symbol
is used to indicate a resistor in a circuit diagram, known as a schematic.Resistance value is designated in units called the "Ohm." A 1000 Ohm resistor is typically shown as 1K-Ohm ( kilo Ohm ), and 1000 K-Ohms is written as 1M-Ohm ( megohm ).
There are two classes of resistors; fixed resistors and the variable resistors. They are also classified according to the material from which they are made. The typical resistor is made of either carbon film or metal film. There are other types as well, but these are the most common.
The resistance value of the resistor is not the only thing to consider when selecting a resistor for use in a circuit. The "tolerance" and the electric power ratings of the resistor are also important.
The tolerance of a resistor denotes how close it is to the actual rated resistence value. For example, a ±5% tolerance would indicate a resistor that is within ±5% of the specified resistance value.
The power rating indicates how much power the resistor can safely tolerate. Just like you wouldnt use a 6 volt flashlight lamp to replace a burned out light in your house, you wouldnt use a 1/8 watt resistor when you should be using a 1/2 watt resistor.
The maximum rated power of the resistor is specified in Watts.
Power is calculated using the square of the current ( I2 ) x the resistance value ( R ) of the resistor. If the maximum rating of the resistor is exceeded, it will become extremely hot, and even burn.
Resistors in electronic circuits are typicaly rated 1/8W, 1/4W, and 1/2W. 1/8W is almost always used in signal circuit applications.
When powering a light emitting diode, a comparatively large current flows through the resistor, so you need to consider the power rating of the resistor you choose.
Rating electric power
For example, to power a 5V circuit using a 12V supply, a three-terminal voltage regulator is usually used.
However, if you try to drop the voltage from 12V to 5V using only a resistor, then you need to calculate the power rating of the resistor as well as the resistance value.
At this time, the current consumed by the 5V circuit needs to be known.
Here are a few ways to find out how much current the circuit demands.
Assemble the circuit and measure the actual current used with a multi-meter. Check the components current use against a standard table.Assume the current consumed is 100 mA (milliamps) in the following example.
7V must be dropped with the resistor. The resistance value of the resistor becomes 7V / 0.1A = 70(ohm). The consumption of electric power for this resistor becomes 0.1A x 0.1A x 70 ohm = 0.7W.
Resistance value
- As for the standard resistance value, the values used can be divided like a logarithm.
For example, in the case of E3, The values [1], [2.2], [4.7] and [10] are used. They divide 10 into three, like a logarithm.
In the case of E6 : [1], [1.5], [2.2], [3.3], [4.7], [6.8], [10].
In the case of E12 : [1], [1.2], [1.5], [1.8], [2.2], [2.7], [3.3], [3.9], [4.7], [5.6], [6.8], [8.2], [10].
It is because of this that the resistance value is seen at a glance to be a discrete value.
The resistance value is displayed using ( the colored bars/the colored stripes ), because the average resistor is too small to have the value printed on it with numbers.
You had better learn the color code, because almost all resistors of 1/2W or less use the color code to display the resistance value.
Fixed Resistors- A fixed resistor is one in which the value of its resistance cannot change.
This is the most general purpose, cheap resistor. Usually the tolerance of the resistance value is ±5%. Power ratings of 1/8W, 1/4W and 1/2W are frequently used.
Carbon film resistors have a disadvantage; they tend to be electrically noisy. Metal film resistors are recommended for use in analog circuits. However, I have never experienced any problems with this noise.
The physical size of the different resistors are as follows.
This resistor is called a Single-In-Line(SIL) resistor network. It is made with many resistors of the same value, all in one package. One side of each resistor is connected with one side of all the other resistors inside. One example of its use would be to control the current in a circuit powering many light emitting diodes (LEDs).
In the photograph on the left, 8 resistors are housed in the package. Each of the leads on the package is one resistor. The ninth lead on the left side is the common lead. The face value of the resistance is printed. ( It depends on the supplier. )
Some resistor networks have a "4S" printed on the top of the resistor network. The 4S indicates that the package contains 4 independent resistors that are not wired together inside. The housing has eight leads instead of nine. The internal wiring of these typical resistor networks has been illustrated below. The size (black part) of the resistor network which I have is as follows: For the type with 9 leads, the thickness is 1.8 mm, the height 5mm, and the width 23 mm. For the types with 8 component leads, the thickness is 1.8 mm, the height 5 mm, and the width 20 mm.
Metal film resistors
- Metal film resistors are used when a higher tolerance (more accurate value) is needed. They are much more accurate in value than carbon film resistors. They have about ±0.05% tolerance. They have about ±0.05% tolerance. I dont use any high tolerance resistors in my circuits. Resistors that are about ±1% are more than sufficient. Ni-Cr (Nichrome) seems to be used for the material of resistor. The metal film resistor is used for bridge circuits, filter circuits, and low-noise analog signal circuits.
 From the top of the photograph 1/8W (tolerance ±1%) 1/4W (tolerance ±1%) 1W (tolerance ±5%) 2W (tolerance ±5%) | 
|
Variable Resistors
There are two general ways in which variable resistors are used. One is the variable resistor which value is easily changed, like the volume adjustment of Radio. The other is semi-fixed resistor that is not meant to be adjusted by anyone but a technician. It is used to adjust the operating condition of the circuit by the technician. Semi-fixed resistors are used to compensate for the inaccuracies of the resistors, and to fine-tune a circuit. The rotation angle of the variable resistor is usually about 300 degrees. Some variable resistors must be turned many times to use the whole range of resistance they offer. This allows for very precise adjustments of their value. These are called "Potentiometers" or "Trimmer Potentiometers.
In the photograph to the left, the variable resistor typically used for volume controls can be seen on the far right. Its value is very easy to adjust.
The four resistors at the center of the photograph are the semi-fixed type. These ones are mounted on the printed circuit board.
The two resistors on the left are the trimmer potentiometers.
This symbol
is used to indicate a variable resistor in a circuit diagram
There are three ways in which a variable resistors value can change according to the rotation angle of its axis.
When type "A" rotates clockwise, at first, the resistance value changes slowly and then in the second half of its axis, it changes very quickly.
The "A" type variable resistor is typically used for the volume control of a radio, for example. It is well suited to adjust a low sound subtly. It suits the characteristics of the ear. The ear hears low sound changes well, but isnt as sensitive to small changes in loud sounds. A larger change is needed as the volume is increased. These "A" type variable resistors are sometimes called "audio taper" potentiometers.
As for type "B", the rotation of the axis and the change of the resistance value are directly related. The rate of change is the same, or linear, throughout the sweep of the axis. This type suits a resistance value adjustment in a circuit, a balance circuit and so on.
They are sometimes called "linear taper" potentiometers.
Type "C" changes exactly the opposite way to type "A". In the early stages of the rotation of the axis, the resistance value changes rapidly, and in the second half, the change occurs more slowly. This type isnt too much used. It is a special use.
As for the variable resistor, most are type "A" or type "B".
Other Resistors
There is another type of resistor other than the carbon-film type and the metal film resistors. It is the wirewound resistor.
A wirewound resistor is made of metal resistance wire, and because of this, they can be manufactured to precise values. Also, high-wattage resistors can be made by using a thick wire material. Wirewound resistors cannot be used for high-frequency circuits. Coils are used in high frequency circuits. Since a wirewound resistor is a wire wrapped around an insulator, it is also a coil, in a manner of speaking. Using one could change the behavior of the circuit. Still another type of resistor is the Ceramic resistor.
The upper one is 10W and is the length of 45 mm, 13 mm thickness.
The lower one is 50W and is the length of 75 mm, 29 mm thickness.
The upper one is has metal fittings attached. These devices are insulated with a ceramic coating.
The photograph on above is a ceramic (or cement) resistor of 5W and is the height of 9 mm, 9 mm depth, 22 mm width
Thermistor ( Thermally sensitive resistor )
The resistance value of the thermistor changes according to temperature.
This part is used as a temperature sensor.
There are mainly three types of thermistor. NTC(Negative Temperature Coefficient Thermistor)
PTC(Positive Temperature Coefficient Thermistor)
CTR(Critical Temperature Resister Thermistor)
The relation between the temperature and the resistance value of the NTC type can be calculated using the following formula. 
As the reference temperature, typically, 25°C is used. The unit with the temperature is the absolute temperature(Value of which 0 was -273°C) in K(Kelvin). 25°C are the 298 kelvins. |
Resistor color code
0 comments:
Post a Comment
Note: only a member of this blog may post a comment.